I built a web app that turns one sentence into a KiCad PCB you can simulate in the browser
For the last months I've been building PCBBrew, a web app for makers: you describe a circuit in plain words and it gives you back a complete project. Not a sketch of an idea, but real files: a KiCad schematic, a routed P
For the last months I've been building PCBBrew, a web app for makers: you describe a circuit in plain words and it gives you back a complete project. Not a sketch of an idea, but real files: a KiCad schematic, a routed PCB, firmware for ESP32, Arduino or Raspberry Pi Pico, and a live simulation in the browser where that firmware actually runs.
The easiest way to explain it is to show one project from start to finish. You can open the same one and play with it, no signup needed: pcbbrew.dev/demo/thermo
Step 1: one sentence
This is the whole request:
A compact desk thermometer with an alarm: ESP32-C3 SuperMini, 0.96" OLED, SHT40 sensor, a small speaker with an LM386 amplifier for the alarm chime, two buttons and USB-C power. Keep the PCB as small as possible.
The assistant asked one question (how to mount the OLED), suggested an alarm setpoint of 28 °C with 1 °C hysteresis, and then did the work: it picked real KiCad parts, read the LM386 datasheet and checked the circuit after every change.
Step 2: a real KiCad schematic
The schematic is a normal KiCad file, split into blocks (controller, USB-C input, audio amplifier, modules) with notes that explain the choices, like the 5.1 kΩ CC pull-downs on the USB-C connector or why the LM386 is left at its standard gain of 20. You can open it in KiCad and keep working on it by hand.
Step 3: placed and routed PCB
Parts are placed and routed automatically: 78 x 64 mm, two layers, with a ground plane under the amplifier. The design rule check finished with zero errors and zero unconnected pads.
Step 4: firmware that compiles
PCBBrew writes the Arduino sketch for the pins it actually wired, and compiles it for the ESP32-C3 (25% of the flash here). From the same page you can flash a real board over USB with Web Serial in Chrome or Edge, no IDE needed.
Step 5: the simulation (my favourite part)
The compiled firmware runs on an emulated ESP32-C3 right in the browser, and the parts around it are live widgets: the OLED shows what the firmware draws, the SHT40 has sliders for temperature and humidity, and the buttons can be clicked. Drag the temperature above 28 °C and the display switches to TEMP ALARM while the speaker plays the chime (press Audio to hear it). The serial monitor shows exactly what the firmware prints.
So you can find firmware bugs, and wiring mistakes, before ordering a single board.
Step 6: 3D and manufacturing files
The assembled board is shown in 3D with its modules, and the project exports everything you need to order it: Gerbers, drill files, BOM and pick-and-place positions, the KiCad project, a STEP model and a PDF with the documentation.
What it does not do (yet)
I'd rather be upfront about the limits:
- The power rails and the firmware are simulated; the LM386 audio stage in this project is not, so the actual loudness still needs a test on real hardware.
- Automatic checks are not a substitute for a review by someone competent before you build or power a board.
- It's meant for low-voltage hobby electronics (30 V and below), not mains.
Try it and tell me what breaks
PCBBrew is in a closed beta for now. The demos are public and run fully in the browser, no account needed:
- Thermometer from this post: pcbbrew.dev/demo/thermo
- More demos and the waitlist: pcbbrew.dev
I'd really like feedback from people who design real boards: what would make you trust a generated schematic, and what does the simulator get wrong? Comments are open.
Originally published by Dev.to WebDev. Aggregated on AIWithGhost for educational purposes — full credit and traffic to the original publisher.




